How do you use the Imax B6AC dual power charger?

Posted on by Drake Andrew

How do you use the Imax B6AC dual power charger?

iMAX B6 Chargers

  1. Plug in the mains adapter and plug it into the battery charger.
  2. Connect the charging lead from the charger to the battery.
  3. Connect the monitoring lead from the battery to the charger.
  4. Place the battery in the charging bag.
  5. Configure the charger using the menu system as follows.

Why does my LiPo charger keep saying connection break?

If you get Connection Break the problem is possibly the cable from the battery to the charger. It could be a dirty connector either on one end of the connector or on the battery itself. Get some electronic contact cleaner and clean all the pins and sockets associated with the cable, battery and charger.

Why do LiPo batteries have 3 wires?

Its common for a LiPO battery pack to have a tap in between every cell, so 3 wires makes sense for a 2S pack. Assuming the color codes are typical, where black is 0V and the Red is the full output, check with a voltmeter I’ll bet you’ll see about 3.5V between the black and white, and about 7V between the black and red.

How does a balance charger work?

The balance charger monitors the voltages of individual cells in the pack via a connector present on the pack. It then adjusts the rate of charge accordingly. This process is referred to as balance charging. It is prudent to mention that LiPo batteries can explode or even catch fire if you do not handle them correctly.

What is a B6 charger?

The IMAX B6 is an advanced multi-function charger, able to charge, balance and discharge Lion, LiPo, LiFe (A123), NiCd and NiMH batteries. It has a wide variety of voltage settings for charging various cell count batteries, as well as a 0.1 amp adjustable charge rate of up to 5 amps.

How many amps can I charge my lipo?

Most LiPo batteries need to be charged rather slowly, compared to NiMH or NiCd batteries. While we would routinely charge a 3000mAh NiMH battery at four or five amps, a LiPo battery of the same capacity should be charged at no more than three amps.

How do I reset my IMAX B6 charger?

How to calibrate IMAX B6

  1. hold Dec (-) and Start button.
  2. plug power adaptor.
  3. wait for calibrating menu.
  4. release Dec (-) and Start button.
  5. wait 20 minutes to warm up to the working temperature.
  6. plug in battery and measure it, compare values between charger and Voltmeter.
  7. if necesarry, then make correction using + and –

How do I connect IMAX B6 ultimate to a 12V battery?

The balance wire attached to the battery must be connected to the charger with the black wire aligned with IMAX B6 Ultimate will be operated with the default value of the essential user settings when it is connected the negative marking. Take care to maintain correct polarity! (Wiring diagram: see below.) to a 12V battery for the first time.

What is b6ac Lipo balance Charger by IMAX?

INTRODUCTION INTRODUCTION Thank you for purchasing the B6AC LiPo Balance Charger by iMAX.This product is a rapid charger with a high performance microprocessor and specialized operating software. Please read this entire operating manual completely and attentively before using this product, as it

What is the difference between IMAX B6 and b6ac V2?

OPERATION SKYRC B6AC V2 is the upgraded version for well-known IMAX B6AC. Compared .. (See the wiring diagram below .). IMAX B6 charger (original and clone) – open source firmware.

Is there an open source firmware for the IMAX B6 Charger?

IMAX B6 charger (original and clone) – open source firmware. Projects that are not Schematic diagram: If not is there a circuit we can build with resistors/ pots to connect a power supply and calibrate the 6 balance outputs?.